李培杰-清华大学机械工程系

李培杰

技术职务：博士，长聘教授

通讯地址：李兆基科技大楼A810

电子邮件：lipj@mail.tsinghua.edu.cn

专业特长：轻金属材料凝固组织控制与成形制造

主要出版物

1. Huang, X., Dong, X., Yang, C., Tian, F., Liu, L., Chen, G., & Li, P. (2017). Investigation of atom distribution in Mg-9wt.% Al melt using small-angle X-ray scattering and molecular dynamics simulation. Journal of Non-Crystalline Solids.

2. Zhang, W., Zhang, W., Li, P., & He, L. (2017). The damage behaviors and microstructural evolution of AZ31B magnesium alloy with gradient texture under hypervelocity impact. Bulletin of the American Physical Society.

3. Zhang, W., Ye, Y., He, L., Li, P., & Zhang, H. (2017). Dynamic mechanical response and microstructural evolution of extruded Mg AZ31B plate over a wide range of strain rates. Journal of Alloys and Compounds, 696, 1067-1079.

4. Dong, X., Huang, X., Liu, L., He, L., & Li, P. (2016). A liquid aluminum alloy electromagnetic transport process for high pressure die casting. Journal of Materials Processing Technology, 234, 217-227.

5．Liu L H, Yang C, Kang L M, et al. A new insight into high-strength Ti62Nb12. 2Fe13. 6Co6. 4Al5. 8 alloys with bimodal microstructure fabricated by semi-solid sintering[J]. Scientific reports, 2016, 6: 23467.

6. Ouyang, P., Li, P., Leksina, E. G., Michurin, S. V., & He, L. (2016). Effect of liquid properties on laser ablation of aluminum and titanium alloys. Applied Surface Science, 360, 880-888.

7．Dong, X., He, L., Huang, X., & Li, P. (2015). Effect of electromagnetic transport process on the improvement of hydrogen porosity defect in A380 aluminum alloy. International Journal of Hydrogen Energy, 40(30), 9287-9297.

8. Dong, X., He, L., Huang, X., & Li, P. (2015). Coupling analysis of the electromagnetic transport of liquid aluminum alloy during casting. Journal of Materials Processing Technology, 222, 197-205.

9. Dong, X., Huang, X., Liu, L., He, L., & Li, P. (2016). A liquid aluminum alloy electromagnetic transport process for high pressure die casting. Journal of Materials Processing Technology, 234, 217-227.

10. Huang, X. S., He, L. J., Mi, G. B., & Li, P. J. (2015). Characteristics of defect bands and their formation mechanisms in A356 wheel fabricated by horizontal squeeze casting. Materials Science and Technology, 31(4), 400-408.

11. Zhang, W. G., He, L. J., Li, P. J., Ye, Y. C., Xue, F. E. N. G., & Novikov, L. S. (2015). Dynamic response and numerical simulation of Al-Sc and Al-Ti alloys under high-speed impact. Transactions of Nonferrous Metals Society of China, 25(2), 559-570.

12. Dong, X., He, L., Mi, G., & Li, P. (2015). Two directional microstructure and effects of nanoscale dispersed Si particles on microhardness and tensile properties of AlSi7Mg melt-spun alloy. Journal of Alloys and Compounds, 618, 609-614.

13. Zhang W G, Ye Y C, He L J, et al. Dynamic response and microstructure control of Al-Sc binary alloy under high-speed impact. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013,578:35-45.

14. Dong X, Mi G, He L, et al. 3D simulation of plane induction electromagnetic pump for the supply of liquid Al-Si alloys during casting. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2013,213(8):1426-1432.

15. Zhao H, Li P, He L. Microstructure and mechanical properties of an asymmetric twin-roll cast AZ31 magnesium alloy strip. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2012,212(8):1670-1675.

16. Zhao H, Li P, He L. Coupled analysis of temperature and flow during twin-roll casting of magnesium alloy strip. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2011,211(6):1197-1202.

17. MI Guangbao, LI Peijie, He Liangju. Structure and property of metal melt I—The number of residual bonds after solid-liquid phase changes. Sci China-Phys Mech Astron, 2010, 53(9): 1571–1577.

18. MI Guangbao, LI Peijie, He Liangju. Structure and property of metal melt Ⅱ—Evolution of atomic clusters in the not high temperature range above liquidus. Sci China Ser G-Phys Mech Astron, 2010, 53(10): 1823—1830. SCI: 650PA

19. Yicong Ye, Peijie Li, L.S. Novikov, V.S. Avilkina, Liangju He. Comparison of residual microstructures associated with impact craters in Al-Sc and Al-Ti alloys. Acta Materialia. 58 (2010) 2520–2526.

20. Yicong Ye, Peijie Li, Liangju He. Valence electron structure analysis of morphologies of Al3Ti and Al3Sc in aluminum alloys. Intermetallics. 18 (2010) 292–297.

联系方式